







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
See the difference
Before
After
Before
After
Before
AfterStanding Seam Metal Roof in Richardson, TX
A standing seam metal roof in Richardson, TX typically costs between $24,000 and $46,000 installed on an average 2,200 to 2,800 square foot home, depending on panel gauge, seam style, and how much deck repair the old roof hides. Standing seam is the concealed-fastener metal roof system where raised vertical seams lock each panel to the next, so the screws that hold the roof down never pierce the surface and never become a leak point. We install it here because Richardson’s mix of 1960s ranch homes and newer infill builds takes a beating from hail and summer heat, and a properly installed metal roof handles both better than almost any other system.
Groundwork Construction Co. of Richardson handles this as a full roofing scope: tear-off, deck inspection, underlayment, panel layout, and trim metal, all under one contract and all backed by our 730-Day Done Right Promise. If it’s not done right, we make it right. Our technicians have up to 12 years of experience with metal panel work, and they arrive background-checked and in uniform. To get a number for your specific house, call (833) 954-4985 and a live person will pick up, day or night.
This page covers the metal side of our Roofing work. For shingle and tile options in the same neighborhood, the broader Roofing page lays out the full menu.

Why Standing Seam Fits Richardson Roofs
Richardson sits in the middle of North Texas hail alley, and we get the storms that come with it: spring supercells that drop golf-ball hail on the Heights Park and Canyon Creek neighborhoods, plus straight-line winds off the Tollway corridor that lift and peel shingles. Standing seam panels get rated for impact and wind uplift far higher than asphalt shingles, and because the fasteners are hidden under the seams, there’s no exposed screw head for hail to shear off or for water to work around. That’s the single biggest reason homeowners here ask us about metal.
The second reason is heat. Richardson summers run long, with attic temperatures that climb fast under a dark shingle roof. A standing seam system with a cool-rated finish reflects a meaningful share of that solar load, and the raised seams create a small channel that vents heat. Homeowners in the older established neighborhoods, especially around the 75080 and 75081 ZIP codes where homes date to the 1960s and 1970s, tell us their upstairs rooms feel noticeably cooler after the switch. That’s a comfort fact, not a marketing line.
We work with well-known roofing manufacturers on the shingle side of the business, and we hold the metal work to the same standard: premium panels, proper underlayment, and trim that matches. The goal is a roof that looks like it was designed for the house, not bolted onto it. Our Richardson service area page has the full picture of how we cover this city.
When You Need Standing Seam Metal Roof
Here’s how to know it’s time to talk about a metal roof instead of another shingle replacement:
- You’re on your second or third shingle roof. If the house has been re-roofed twice in its life, the math favors metal. A standing seam system that’s installed correctly outlasts multiple shingle cycles, and you stop paying for tear-off every 15 to 20 years.
- You’ve filed more than one hail claim. Homeowners near Lookout Park and the Arapaho corridor who’ve had two or more storm claims in a decade often find their carrier is the one pushing metal. It’s worth calling before the next storm rather than after.
- Your old roof is leaking at valleys or penetrations. Roof leaks that keep coming back after a patch usually trace to failed flashing around chimneys, plumbing vents, or skylights. Standing seam handles penetrations with custom metal, which removes the repeat-failure spot.
- You’re adding solar or plan to. Standing seam panels support clamp-on solar mounts that don’t require drilling into the roof, which the solar installers we work alongside prefer. If panels are in the two-year plan, install the roof right the first time.
- You want a roof done once. For homeowners who plan to stay put, a metal roof is the last roof they’ll buy. The upfront cost is real, but the cost per year over the life of the system is lower than shingle, especially once you factor in storm-claim hassles.
- You like the look. Standing seam has a clean, modern profile that reads well on mid-century ranch homes and contemporary builds. We can match colors to existing trim and fascia so the roof looks intentional.

Our Standing Seam Metal Roof Process
Every standing seam job on a Richardson home follows the same sequence, and you’ll know what’s happening at each stage before we start:
- Free estimate and design consult. We measure the roof, check the existing deck, and walk you through panel profile, seam style, color, and gauge. You get upfront pricing in writing, and the number you see is the number you pay. No-hassle, no surprises.
- Material and color selection. We help you pick from the finish options that make sense for a Texas climate, and we set a start date. If financing helps, we offer 0% financing for 18 months, plus $1,000 off projects over $10,000.
- Tear-off and deck inspection. We strip the old roof, inspect every sheet of decking, and replace any soft or delaminated wood we find. A metal roof is only as good as the deck under it, so this step isn’t negotiable.
- Underlayment and panel installation. We install the underlayment rated for our heat and hail, then lay and lock the standing seam panels. The concealed clamps or fasteners get set at the correct spacing for the wind zone, and every panel seam gets rolled flat.
- Trim, flashing, and penetrations. Ridge caps, valleys, gable trim, and all the custom flashing around chimneys and vents go on to spec. This is where a metal roof succeeds or fails, and it’s the detail we spend the most time on.
- Final walkthrough and warranty handoff. We walk the roof with you, clean up the site, and hand off the documentation for your finish warranty and our 730-Day Done Right Promise. Every technician on the crew is background-checked and in uniform.
Standing Seam Metal Roof Pricing in Richardson
Standing seam metal roof pricing in Richardson typically runs $10 to $18 per square foot installed, or $24,000 to $46,000 on a full residential roof. The wide range comes from the variables below. We price every job in writing before a panel is ordered, and that’s the number you pay.
| Line item | Typical range |
|---|---|
| Tear-off and disposal of old roof | $2,500 – $5,000 |
| Standing seam panels and installation | $16,000 – $32,000 |
| Underlayment and deck repair (as needed) | $900 – $3,500 |
| Trim, flashing, and ridge caps | $1,800 – $4,500 |
| Custom penetrations (chimney, skylights) | $600 – $2,000 |
| Total installed | $24,000 – $46,000 |
What drives the number up or down:
- Panel gauge and seam height. Heavier gauge and taller seams cost more per panel but perform better under hail and wind. We help you choose the gauge that’s right for your exposure, not the cheapest one.
- Roof complexity. A simple gable roof goes on fast. A hip roof with multiple valleys and dormers takes more cut work, more trim, and more time.
- Deck condition. Soft decking from old leaks has to be replaced, and that shows up in the line-item quote rather than a surprise change order.
- Color and finish. Premium finishes cost more, but they also hold up better to Texas sun. We show you the tradeoff in person.
- Access. Two-story homes and tight lots off Central Expressway take longer to stage and remove debris from.
The estimate and design consult are free. If a metal roof is over your budget this year, we’ll tell you what a shingle replacement buys you in the meantime. We don’t push a product the house doesn’t need.
Common Questions About Standing Seam Metal Roofs in Richardson
How much does a standing seam metal roof cost in Richardson?
A standing seam metal roof in Richardson runs $24,000 to $46,000 installed on a typical single-family home, or roughly $10 to $18 per square foot. Call (833) 954-4985 for an exact quote on your roof, and the estimate is free.
Can you install a standing seam metal roof over my old shingles?
We don’t recommend it, and we won’t do it on a Richardson home. Installing standing seam over existing shingles traps moisture and hides deck problems that a metal roof can’t tolerate. We tear off, inspect the deck, and install on a clean surface every time.
Will a metal roof increase my home insurance premium?
It usually lowers it. Many Texas carriers offer discounts on impact-resistant metal roofing, though the exact credit depends on your policy. Call us at (833) 954-4985 and we can walk through the documentation your carrier will want.
How long does a standing seam metal roof last in Texas heat?
Forty years and up on a properly installed system, often longer. The concealed fasteners are the key. Because no screws pierce the surface, there’s no fastener to rust out and no penetration for water to work behind. Our 730-Day Done Right Promise covers the workmanship side in writing.
Standing seam metal roofing isn’t the cheapest roof you’ll buy, and we won’t pretend otherwise. It’s the one you buy once. If you want a straight answer on cost, timing, and whether metal makes sense for your house, call Groundwork Construction Co. of Richardson at (833) 954-4985. A live person answers, 24 hours a day, seven days a week, and the estimate is free. You can also review the broader Roofing options or check our Richardson service area page to see what else we cover.
Written by the team at Groundwork Construction Co. of Richardson, serving Richardson.


