







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Chain Link Fence in Richardson, TX: Storm-Ready Cost, Timeline, and What to Expect
A chain link fence in Richardson typically runs $3,500 – $9,000 installed, depending on height, footage, gauge, and whether it’s a straight run or a lot loaded with gates and turns. Most residential jobs wrap in 1 – 2 days once we start. Before you commit, call (833) 954-4985 and we’ll walk your property, mark the corners, and hand you a written number built for North Texas wind.
Here’s the part most bids skip: in Richardson, a fence is judged by how it holds through a spring hail-and-wind season, not how it looks the week it’s installed. We build for that first.
How We Build a Chain Link Fence in Richardson – Stage by Stage

The sequence below is what actually happens on a Richardson lot, from first walk to final walkthrough. It’s not a sales pitch; it’s the job.
Stage 1: Site walk and layout (day 1, about 60 – 90 minutes)
We confirm property lines against your survey, locate utilities, and check setback and lot-coverage rules that apply to your block in Richardson. You decide the run line and gate locations here, because once the string goes down, moving a gate is a change order. On older platted blocks near Central Expressway, the survey is the homework that keeps surprises out of the bid.
Stage 2: Post holes and footing depth (day 1 – 2)
Terminal posts, corner posts, and gate posts go deeper than line posts, and on Richardson’s expansive clay the set matters more than the fence itself. We set posts in concrete and hold them to a level that won’t lean the first time the clay swells and shrinks after a wet spring. This is the stage that separates a ten-year fence from a four-year fence.
Stage 3: Framing the chain link line (day 2)
Top rail, tension bands, and the terminal bracing go in next. You’ll see the skeleton up before any mesh is stretched. This is your checkpoint: walk the line and confirm heights and gate openings match what you approved.
Stage 4: Stretching and tensioning the fabric (day 2)
We stretch the mesh tight against top and bottom rail, tie it off at every terminal, and hang your gates. A loose chain link fence rattles in a 40-mph gust and fatigues its fittings; a properly tensioned one doesn’t. We check gate swing and gate-post plumb before we call it finished.
Stage 5: Final walk and inspection (day 2 – 3)
We sweep the line with you, check every tie and gate, and clean up the site. If your property has a permit requirement, we handle the inspection sign-off. You leave knowing exactly who to call if anything needs tightening. All of it runs under the 730-Day Done Right Promise, backed in writing.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
What You’ll Choose Between on a Chain Link Fence
The options below are the real decisions that shape a Richardson chain link fence. We’ll walk you through each on-site, but here’s an honest rundown so you come in prepared.
- Gauge (fabric thickness): 11-gauge is standard and holds up fine for most residential runs; 9-gauge is heavier and better where kids, pets, or wind load are a concern. The heavier fabric costs more up front but lasts longer through wind events.
- Coating and finish: Galvanized handles the weather well on its own; vinyl-coated in black or green costs a bit more and looks cleaner against brick and landscaping. Both hold up in North Texas sun if installed correctly.
- Height: 4-foot is the common residential line; 5- and 6-foot runs handle privacy and pet containment better and cost more per foot.
- Gates: Walk gates and drive gates are priced separately. You’ll pick swing direction, size, and whether you want a self-closing or self-latching mechanism. This is where most of your decisions happen.
- Top rail and bracing: A standard top rail with proper terminal bracing survives wind far better than a bargain frame. We don’t cut corners here, and we’ll tell you if a bid you’re comparing does.
On the materials side, we source through our vetted brand partners so the fence you spec is the fence you get. Richardson homeowners often pair a chain link run with a Door Installation in Richardson project for a new gate, or with ADU Site Prep & Utilities in Richardson when a back-lot build means the fence line has to move.
What a Chain Link Fence Costs in Richardson, TX

Plan on $3,500 – $9,000 for a residential chain link fence in Richardson. That’s the number we put on most jobs, and it moves based on the variables below. A straight backyard run of standard height lands on the low end; a larger lot with multiple gates and heavier gauge lands high.
| Line Item | Typical Range |
|---|---|
| Standard residential run (galvanized, 4 – 5 ft) | $3,500 – $6,000 |
| Heavier gauge / vinyl-coated upgrade | $4,500 – $7,500 |
| Gate additions and hardware | $350 – $1,200 each |
| Larger lot, multiple runs and terminals | $7,000 – $9,000+ |
What moves the number:
- Footage and lot shape: A simple rectangle is cheaper than an irregular line with corners and jogs.
- Existing removal: Tearing out an old fence adds labor; a clean lot doesn’t.
- Gauge and coating: Heavier fabric and vinyl finishes push toward the high end.
- Gates: Each gate is a separate line item with its own hardware.
- Permit scope: If your Richardson property triggers a permit, that’s a line item, not a surprise.
A written estimate includes layout, posts, concrete, rails, fabric, gates, and cleanup. It doesn’t include things like hauling off an old fence unless we quote it, or specialty gates. We put it all in writing so there’s no mystery on the invoice.
See the difference
Before
After
Before
After
Before
AfterWhat Richardson Homes Specifically Do to This Job
Richardson’s mix of work is unlike the newer suburbs. The core is 1950s – 1970s single-story brick ranch homes, many on pier-and-beam foundations, sitting alongside a growing layer of tear-down and infill builds on the same small lots. That older stock means fence lines often run over settled clay and roots, weather-beaten posts from decades of storms, and gates that no longer swing true. The newer infill layer means we’re also building to modern code and lot-coverage rules on a tight lot where the survey has to be right the first time.
North Texas clay and spring hail and wind are the other half of the story. On older platted blocks near Central Expressway, the clay swells and shrinks and the wind keeps working on every joint. That’s where a lot of the fence failures we see start. Add in the city’s active redevelopment posture and demolition inspection is a normal part of the job here, not a rarity. Our Richardson service area covers the full city, and if your run is part of a bigger project, that’s a full Fence Installation in Richardson conversation.
Serving Richardson, TX – Our Local Coverage Area
We serve Richardson and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Chain Link Fence in Richardson

Most residential chain link fences in Richardson take 1 – 2 days from start to final walk, weather permitting. Larger lots with multiple gates and heavier gauge can stretch to 3 days. The timeline depends on footage, gate count, and whether the old fence has to come out first. Call (833) 954-4985 for a firm schedule once we’ve seen the lot.
It depends on where the fence line sits relative to setbacks and whether your property is in a regulated or historic area; some runs need a permit and some don’t. We check that for your specific lot before quoting so the cost is real. We pull what’s required and see it through inspection, and the permit cost shows up as a line item, not a hidden fee.
In most cases, yes. Posts are set around existing utilities, and we locate before we dig, so plumbing and buried lines stay where they are. If your run crosses a line we can’t avoid, we’ll show you the alternative layout on-site. That’s the kind of thing a site walk sorts out, and it’s free to find out. Call (833) 954-4985 to schedule yours.
A residential chain link fence in Richardson runs $3,500 – $9,000 installed, with standard runs at the lower end and larger lots with gates and heavier gauge at the upper end. Footage, gauge, coating, gate count, removal, and permit scope all move the number. Call (833) 954-4985 and we’ll give you an exact figure after a walk, no guesswork.
Workmanship is covered by our 730-Day Done Right Promise: if it isn’t done right, we make it right. That covers post setting, tensioning, and fence installation, and it’s backed in writing. Have a question on a stretch of fence a year or two in? Call us and a live person will pick up. (833) 954-4985
Get a Free Chain Link Fence Estimate in Richardson
A chain link fence is a straightforward job with a fixed number and a written estimate, not a guess. Call Groundwork Construction Co. of Richardson at (833) 954-4985 to schedule your free on-site estimate. We’ll walk the line, check property lines and setbacks, and hand you an itemized quote with no surprises. Upfront pricing, live person 24/7, work covered by the 730-Day Done Right Promise. Same crew and standards across every Fence Installation project we take on.
Written by the team at Groundwork Construction Co.












