







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Concrete Driveways & Concrete Work in Garland, TX: What to Expect
Concrete driveways and concrete work in Garland, TX run $4,500 to $12,000 for a full driveway installation, with most jobs finished in 3 to 5 days once the pour starts. Replacement runs $5,000 to $14,000, sealing a new slab adds $250 to $700, and repair of a cracked or settled apron is often folded into the same project. Call (833) 954-4985 for a free on-site estimate with a written line-item quote.
How We Build a Concrete Driveway in Garland, Start to Finish

Concrete work on a Garland lot is mostly about what’s underneath. The slab is only as good as the base, the grade, and the joints, so the first two days matter more than the pour. Here’s the real sequence.
Stage 1: Site walk and layout (day 1, about 1 hour)
We walk the driveway line with you, check the utility locate marks, and confirm the width you actually need. On Garland’s older streets, tight lot lines and narrow side yards often push the driveway within a foot of the property line. You decide the final width, the slope away from the garage, and where any expansion joints land. We mark the cut line in paint before anything moves.
Stage 2: Demolition and haul-off (day 1, 3 to 6 hours)
Old concrete gets broken out with a skid-steer breaker and hauled off the same day. A standard two-car slab is roughly 10 to 14 cubic yards of debris. If the existing driveway was poured over a failing base, we remove the subbase too instead of paving on top of a problem. You’ll see the subgrade exposed by end of day, which is the moment to look for roots, soft spots, or old plumbing trenches.
Stage 3: Grading, base, and forms (day 2, full day)
We cut and compact the subgrade, then place 4 to 6 inches of compacted crushed base under the slab. Forms go up on both edges, and on Garland lots with mature trees we add root barriers where pecan and oak roots run under the new slab line. The base gets compacted in lifts with a plate compactor; a slab poured over loose fill is the number one reason driveways crack within a year.
Stage 4: Rebar, inspection, and pour (day 3, pour in the morning)
We set #3 or #4 rebar on chairs at 18 to 24 inches on center, depending on slab thickness and whether any vehicle heavier than a passenger car will use it. Thickness runs 4 inches for standard residential and 5 to 6 inches where a truck or trailer parks. If the job touches the right-of-way, the city inspection happens before the pour. The pour itself takes 2 to 4 hours, then the slab needs to sit undisturbed.
Stage 5: Cure, control joints, and finishing (days 3 to 8)
Control joints get cut within 12 to 24 hours of the pour, and we apply a cure compound or wet-cure the slab for 5 to 7 days depending on weather. You can walk on it after 24 to 48 hours and drive on it after 7 days. Full strength takes 28 days. Sealing, if you want it, comes after the 28-day cure.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Concrete Choices You’ll Actually Make
Concrete is not a single product. The decisions below are the ones that separate a driveway that lasts 30 years from one that spalls in five.
- Standard broom finish vs. exposed aggregate: broom is the workhorse, costs the least, and gives the best traction in Garland’s wet spring weather. Exposed aggregate adds roughly 15 to 25 percent to the cost, holds up well, and hides tire marks. It’s harder to shovel and rougher on bare feet.
- 4000 psi vs. 3500 psi mix: we pour 4000 psi on every driveway. The cost difference is small. The durability difference over North Texas temperature swings is not.
- Rebar vs. mesh: welded wire mesh is cheaper and adequate for light foot traffic. Rebar is the correct choice for anything a vehicle drives on, and it’s what we use under driveways.
- 4-inch vs. 5 to 6-inch slab: 4 inches handles cars and light SUVs. If you park a truck, trailer, or RV, go thicker. The extra yardage is the cheapest insurance on the job.
- Integral color or stain: color mixed into the concrete costs more than surface stain but doesn’t fade. For a stamped or decorative look, that’s a separate conversation – Driveway & Pavers in Garland covers the paver and stamped options in depth if you want to compare.
On paver borders and retaining edging, homeowners sometimes ask about Boral or Tamko accent products to frame a concrete pour. We’ll show you what’s realistic for your budget rather than upselling a finish your lot doesn’t need.
What Concrete Driveways & Concrete Work Costs in Garland, TX

Residential concrete driveway installation in Garland runs $4,500 to $12,000. Replacement of an existing slab, including demo and haul-off, runs $5,000 to $14,000. Sealing a cured driveway lands at $250 to $700. Those are the ranges; here’s what pushes a job toward the top or bottom.
- Square footage: a single-car apron and a three-car drive are different projects. Most Garland lots land between 400 and 700 square feet of driveway.
- Demo and haul-off: breaking out and removing an old slab adds $800 to $2,000 depending on thickness and access.
- Base condition: soft fill, root intrusion, or a failing subbase means over-excavation and new base material. This is where jobs legitimately come in above the estimate, so we test the base before quoting.
- Access constraints: a narrow side yard means a smaller truck and more hand work. That adds labor, not material.
- Permit scope and inspection: work in the public right-of-way or a new curb cut needs a permit and city inspection. That adds lead time and a permit fee.
Every written estimate itemizes demo, base, rebar, thickness, finish, and disposal as its own line. Nothing bundled, no change orders once the work starts. Groundwork backs every pour with the 730-Day Done Right Promise, and 0% financing for 18 months is available if you’d rather spread the cost.
See the difference
Before
After
Before
After
Before
AfterWhat Garland Homes Specifically Do to This Job
Garland is a mid-century city. The housing went up almost entirely in a handful of postwar booms – the 1950s and 60s core near downtown Garland and the 75040/75041 ZIP codes, then the 1970s and 80s ranch sprawl out toward Rowlett and Sachse – which means we’re almost always working on an existing slab-on-grade house, not a fresh lot. On these older properties the original driveway is often the narrowest one on the block, poured when a family had one car, which is why so many Garland homeowners widen as they replace. The other recurring issue is the blackland clay under every one of these yards. It swells in wet winters and shrinks in dry summers, and that movement is what cracks most driveways and pushes them out of level at the garage apron. By the time a slab is visibly heaving, the base underneath has usually been fighting the soil for years. Mature pecan and oak canopies in the older sections also put roots right under the driveway line and drop enough debris to hide early cracking. Work that touches the public right-of-way or the driveway approach gets a city permit and inspection before we pour, and we pull it as part of the job.
If the driveway is one piece of a wider project, our Driveway & Pavers service covers the rest of the hardscape, and homeowners often pair a new driveway with Door Installation in Garland while the front approach is torn up. We also handle ADU Site Prep & Utilities in Garland for anyone adding a unit where the driveway needs to run. We work across Garland and the surrounding communities.
Serving Garland, TX – Our Local Coverage Area
We serve Garland and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Concrete Driveways & Concrete Work in Garland

Plan on 3 to 5 days of construction plus a 7-day wait before you drive on it. Demolition, base prep, forming, rebar, and pour take three working days on a typical Garland driveway, and weather can stretch the pour by a day. Full cure to 28 days before sealing. Call (833) 954-4985 to schedule a free estimate and we’ll give you a firm date range.
You do if the work touches the public right-of-way, the driveway approach, or a new curb cut. Interior driveway work on your own lot generally doesn’t require one. We handle the permit and the city inspection as part of the job so nothing sits waiting on paperwork. Call for a free estimate and we’ll tell you up front whether your project needs a permit.
In most cases, yes. Sewer and water lines run under Garland driveways, but the slab is poured over them with rebar and base clear, so nothing has to move. If the existing slab has to be raised or a utility needs to be replaced, that’s discussed and priced before we start. Estimates are free – call (833) 954-4985.
A full concrete driveway installation runs $4,500 to $12,000, and replacement runs $5,000 to $14,000. Sealing is $250 to $700. Width, demo, base condition, and access are the main variables. Call (833) 954-4985 for an exact number on your property.
Every driveway we pour is covered by the 730-Day Done Right Promise – if it’s not done right, we make it right. That’s one of the longest workmanship guarantees in residential construction, and it covers the pour, not just the paperwork. Call to talk through the details before you commit.
Get a Free Estimate on Concrete Driveways & Concrete Work in Garland
A free on-site estimate is the next step. Call (833) 954-4985 and a live person answers, any hour, any day. We’ll ask about your driveway’s width and condition, set a time to walk the site, and hand you a written line-item quote with the thickness, rebar, base, and finish spelled out, plus any permit needed on your Garland property. You’ll know exactly what the number covers before you sign anything.
Written by the team at Groundwork Construction Co.












